This page was exported from New Lead2pass PDF And VCE Ensure IT Exam Pass 100% [ https://www.dumps4microsoft.com ] Export date:Mon Dec 30 14:43:20 2024 / +0000 GMT ___________________________________________________ Title: [April 2018] Free Downloading 300-135 Exam Dumps PDF From Lead2pass 181q --------------------------------------------------- Free Lead2pass 300-135 PDF Download 100% Pass Exam 300-135: https://www.lead2pass.com/300-135.html QUESTION 21The following commands are issued on a Cisco Router: Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1Router(configuration)#exitRouter#debug ip packet 199 What will the debug output on the console show? A.    All IP packets passing through the routerB.    Only IP packets with the source address of 10.1.1.1C.    All IP packets from 10.1.1.1 to 172.16.1.1D.    All IP Packets between 10.1.1.1 and 172.16.1.1 Answer: DExplanation:In this example, the "debug ip packet" command is tied to access list 199, specifying which IP packets should be debugged. Access list 199 contains two lines, one going from the host with IP address 10.1.1.1 to 172.16.1.1 and the other specifying all TCP packets from host 172.16.1.1 to 10.1.1.1. QUESTION 22What level of logging is enabled on a Router where the following logs are seen? %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up A.    alertsB.    criticalC.    errorsD.    notifications Answer: DExplanation:Cisco routers, switches, PIX and ASA firewalls prioritize log messages into 8 levels (0-7), as shown below: LevelLevel NameDescription0 Emergencies System is unusable1 Alerts Immediate action needed2 Critical Critical conditions3 Errors Error conditions4 Warnings Warning conditions5 Notifications Informational messages6 Informational Normal but significant conditions7 Debugging Debugging messages When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case we can see that logging level of 3 (as seen by the 3 in "LINK-3-UPDOWN") and level 5 (as seen by the 5 in "LINEPROTO-5-UPDOWN") are shown, which means that logging level 5 must have been configured. As shown by the table, logging level 5 is Notifications. QUESTION 23You have the followings commands on your Cisco Router: ip ftp username adminip ftp password backup You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands? A.    ip http username adminB.    ip http client username adminC.    ip http password backupD.    ip http client password backupE.    ip http server username adminF.    ip http server password backup Answer: BDExplanation:Configuring the HTTP ClientPerform this task to enable the HTTP client and configure optional client characteristics. The standard HTTP 1.1 client and the secure HTTP client are always enabled. No commands exist to disable the HTTP client. For information about configuring optional characteristics for the HTTPS client, see the HTTPS-HTTP Server and Client with SSL 3.0, Release 12.2(15)T, feature module. SUMMARY STEPS1. enable2. configure terminal3. ip http client cache {ager interval minutes | memory {file file-size-limit | pool pool-size-limit}4. ip http client connection {forceclose | idle timeout seconds | retry count | timeout seconds}5. ip http client password password6. ip http client proxy-server proxy-name proxy-port port-number7. ip http client response timeout seconds8. ip http client source-interface type number9. ip http client username username Reference: HTTP 1.1 Web Server and Client.http://www.cisco.com/en/US/docs/ios/netmgmt/configuration/guide/nm_http_web.html QUESTION 24You have 2 NTP servers in your network - 10.1.1.1 and 10.1.1.2.You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to10.1.1.1. Which commands will you use to configure the router? A.    ntp server 10.1.1.1ntp server 10.1.1.2B.    ntp server 10.1.1.1ntp server 10.1.1.2 primaryC.    ntp server 10.1.1.1ntp server 10.1.1.2 preferD.    ntp server 10.1.1.1 fallbackntp server 10.1.1.2 Answer: CExplanation:A router can be configured to prefer an NTP source over another. A preferred server's responses are discarded only if they vary dramatically from the other time sources. Otherwise, the preferred server is used for synchronization without consideration of the other time sources. Preferred servers are usually specified when they are known to be extremely accurate. To specify a preferred server, use the prefer keyword appended to the ntp server command. The following example tells the router to prefer TimeServerOne over TimeServerTwo:Router#config terminalEnter configuration commands, one per line. End with CNTL/Z. Router(config)#ntp server TimeServerOne preferRouter(config)#ntp server TimeServerTwoRouter(config)#^Z QUESTION 25The following command is issued on a Cisco Router: Router(configuration)#logging console warnings Which alerts will be seen on the console? A.    Warnings onlyB.    debugging, informational, notifications, warningsC.    warnings, errors, critical, alerts, emergenciesD.    notifications, warnings, errorsE.    warnings, errors, critical, alerts Answer: CExplanation:Cisco routers prioritize log messages into 8 levels (0-7), as shown below: LevelLevel NameDescription0 Emergencies System is unusable1 Alerts Immediate action needed2 Critical Critical conditions3 Errors Error conditions4 Warnings Warning conditions5 Notifications Informational messages6 Informational Normal but significant conditions7 Debugging Debugging messages When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case, when you enable console logging of warning messages (level 4), it will log levels 0-4, making the correct answer warnings, errors, critical, alerts, and emergencies. QUESTION 26Which two of the following options are categories of Network Maintenance tasks? A.    FirefightingB.    Interrupt-drivenC.    Policy-basedD.    StructuredE.    Foundational Answer: BDExplanation:Proactive Versus Reactive Network Maintenance:Network maintenance tasks can be categorized as one of the following: Structured tasks: Performed as a predefined plan.Interrupt-driven tasks: Involve resolving issues as they are reported. QUESTION 27A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems. PC2 in VLAN 200 is unable to ping the gateway address 172.16.200.1; identify the issue. A.    VTP domain name mismatch on SW4B.    VLAN 200 not configured on SW1C.    VLAN 200 not configured on SW2D.    VLAN 200 not configured on SW4 Answer: D QUESTION 28A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.Which of statement is true regarding STP issue identified with switches in the given topology? A.    Loopguard configured on the New_Switch places the ports in loop inconsistent stateB.    Rootguard configured on SW1 places the ports in root inconsistent stateC.    Bpduguard configured on the New_Switch places the access ports in error-disableD.    Rootguard configured on SW2 places the ports in root inconsistent state Answer: A 300-135 dumps full version (PDF&VCE): https://www.lead2pass.com/300-135.html Large amount of free 300-135 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDZmFQVlZDZnpLejA Maybe you also need: 300-101 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDakxVRXg3aUpmTE0 300-115 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDM0pqaFJWUXVuM2M --------------------------------------------------- Images: http://examgod.com/l2pimage/50fe72ce7f37_C9D3/271_thumb.jpg http://examgod.com/l2pimage/50fe72ce7f37_C9D3/281_thumb.jpg --------------------------------------------------- --------------------------------------------------- Post date: 2018-04-04 07:26:30 Post date GMT: 2018-04-04 07:26:30 Post modified date: 2018-04-04 07:26:30 Post modified date GMT: 2018-04-04 07:26:30 ____________________________________________________________________________________________ Export of Post and Page as text file has been powered by [ Universal Post Manager ] plugin from www.gconverters.com